You need to know about Key Machine from the Key Machine manufacturer, supplier, wholesaler, distributor, and factory

Key Machine

Multi-functional keys duplicating machine, can be copied all kinds of double-sided grooved keys.

Equipped with C/W Tungsten Carbide Cutter
Clear Depth Calibration on Guide Adjusting Dial and easy amendment.
Vise handles get ball bearing device, tighten and flexible operation.
Specific designed jaw handles to accurately cut bit & double bit keys.
Equipped with LED lamp.
Thermal Circuit breaker : Power off to avoid any damage on the condition that the circuit is overload fuse.
With lightweight easy to used.

Left Carriage

The 4 way vise can refer your need to hold till to 128mm key and any type of double side grooved key.
You can use the key gauge to place shouldered keys on right position of grooved vise
The new design of 4 way vise present you more precise measurements while duplicating keys.
Our engineers have added an extra fixing screw below the guide is to protect the Cutter and vise not to be damaged while duplicating keys.

Right Carriage

The vise duplicate 128mm keys and special / unusual keys that no extra adapter is needed. Ex. Semi-circular key, Square key, Round shaft key.

Specifications:
Dimensions：360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

Key Machine

Multi-functional keys duplicating machine, can be copied all kinds of double-sided grooved keys.

Equipped with HSS plated titanium blade and Tungsten steel saw blade.
Clear Depth Calibration on Guide Adjusting Dial and easy amendment.
Vise handles get ball bearing device, tighten and flexible operation.
Specific designed jaw handles to accurately cut bit & double bit keys.
Equipped with LED lamp.
Thermal Circuit breaker : Power off to avoid any damage on the condition that the circuit is overload fuse.
With lightweight easy to used.

Left Carriage

The 4 way vise can refer your need to hold till to 128mm key and any type of double side grooved key.
You can use the key gauge to place shouldered keys on right position of grooved vise
The new design of 4 way vise present you more precise measurements while duplicating keys.
Our engineers have added an extra fixing screw below the guide is to protect the Cutter and vise not to be damaged while duplicating keys.

Right Carriage

The vise duplicate 128mm keys and special / unusual keys that no extra adapter is needed. Ex. Semi-circular key, Square key, Round shaft key.

Specifications:
Dimensions：360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

Duplicate Key Maker

The GL-750 key machine is the top of the line cylinder key cutting machine for professional locksmiths. It will cut most cylinder keys including standard motorcycle / car cylinder keys and cruciform keys. This model delivers unsurpassed accuracy and cutting performance.

The 4-way jaws can refer your need to hold till to 120mm key and any type of double side grooved key
Automatic power on-off controlled by micro-switch, activated by raising or lowering the carriage.
Carriage design flexibility to provide adequate pressure when cutting keys to increase the accuracy of key.
Lamp inside the machine design can directly illuminate the surface of the carriage and vise jaw.
Equipped with V type angle cutter.
Extra fixing screw below the guide which is to protect the cutter and jaws not to be damaged while duplicating keys.

Specifications:
Dimensions: 330 mm(W)*370mm(D)*290mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 Cuft

Motor: Single Phase, 1/5 Hp, R.P.M. 1720
110V or 220v, 50 HZ or 60 HZ

Key Duplicate Machine

The duplicator is designed for duplicating "FLAT" keys, such as those used with popular safe deposit and locker locks.
Equipped with slotting saw of tungsten carbide material.
Can make lever & side bitted flat key of any length.
Can make key "arc" cutting.
New designed vise jaw rotate button, easily for duplicating.
Highly accuracy and efficiency.

Specifications:
Dimensions: 300 mm(W)*300mm(D)*320mm(H)
N.W.: 14 Kg G.W.: 16 Kg
Meas. 2.48 CUFT
Motor: 110V or 220v，50 HZ or 60 HZ

Synchronous tilt designed with flat oblique key

Synchronous tilt designed with flat oblique key
Unique system with synchronized tilting axis, adjustable angle between 0-45 degrees, suitable for copying the flat oblique keys
Equipped with a new calibrated tracer accuracy adjustment button, each rotation is 0.02mm, the depth can be positioned
New design touch operation panel: Motor start button, Tracer depth adjustment button, Motor speed indicator, Motor RPM adjusting knob, LED ON/OFF switch
Equipped with a cross-slide smart control, specially designed for serpentine and grooved keys
Lock this button, next to the female key groove, resulting in the elastic effect of the automatic modeling
Built-in tubular key clamp pointing for easy duplicating
Equipped with a brushless inverter motor, quiet and energy saving
Equipped with a new quick release fixture for easy calibration assembly
Equipped with new tungsten steel cutters

Synchronous tilt designed with flat oblique key

Synchronous tilt designed with flat oblique key
Unique system with synchronized tilting axis, adjustable angle between 0-45 degrees, suitable for copying the flat oblique keys
Equipped with a new calibrated tracer accuracy adjustment button, each rotation is 0.02mm, the depth can be positioned
New design touch operation panel: Motor start button, Tracer depth adjustment button, Motor speed indicator, Motor RPM adjusting knob, LED ON/OFF switch
Equipped with a cross-slide smart control, specially designed for serpentine and grooved keys
Lock this button, next to the key groove, resulting in the elastic effect of the automatic modeling
Equipped with the adaptor for tubular keys to duplicate
Equipped with a brushless inverter motor, quiet and energy saving
Equipped with a new quick release fixture for easy calibration assembly
Equipped with new tungsten steel cutters
Equipped with a four-grid milling cutters and tracers fixture for easy access

Multifunctional duplicating key machine

Multifunctional duplicating key machine
Suitable for copying drilling and snake groove cutting keys, such as KABA, KESO, BENZ…etc
Equipped with a new calibrated tracer accuracy adjustment button, each rotation is 0.02mm, the depth can be positioned
New design touch operation panel: Motor start button, Tracer depth adjustment button﹑Motor speed indicator, Motor RPM adjusting knob, LED ON/OFF switch
Equipped with a cross-slide smart control, specially designed for serpentine and grooved keys
Lock this button, next to the key groove, resulting in the elastic effect of the automatic modeling
Equipped with the adaptor for tubular keys to duplicate
Equipped with a brushless inverter motor, quiet and energy saving
Equipped with a new quick release fixture for easy calibration assembly
Equipped with new tungsten steel cutters

Multifunctional duplicating key machine

Synchronized turning design of clamp can be used to cut round keys with dimples around like SB keys.
Multi-functional key clamp can be used to common flat dimple key & snake /profile cutting keys like KABA, KESO & Benz.
Equipped with a new calibrated tracer accuracy adjustment button, each rotation is 0.02mm, the depth can be positioned
New design touch operation panel: Motor start button, Tracer depth adjustment button, Motor speed indicator, Motor RPM adjusting knob, LED ON/OFF switch
Equipped with a cross-slide smart control, specially designed for serpentine and grooved keys
Lock this button, next to the key groove, resulting in the elastic effect of the automatic modeling
Equipped with the latest design and new four-sided vise, depending on the type of key, there are four-sided, which can be selected according to the needs, rotated, and work more smoothly.
Equipped with a DC brushless inverter motor, quiet and energy saving
Equipped with new tungsten steel cutters

Key Duplicating Machine

Newly developed four-sided rotating vise with drill and slotting key
Multi-functional key clamp can be used to common flat dimple key & snake /profile cutting keys like KABA, KESO & Benz.
Equipped with a new calibrated tracer accuracy adjustment button, each rotation is 0.02mm, the depth can be positioned
New design touch operation panel: Motor start button, Tracer depth adjustment button, Motor speed indicator, Motor RPM adjusting knob, LED ON/OFF switch
Equipped with a cross-slide smart control, specially designed for serpentine and grooved keys
Lock this button, next to the key groove, resulting in the elastic effect of the automatic modeling
Equipped with the latest design and new four-sided vise, depending on the type of key, there are four-sided, which can be selected according to the needs, rotated, and work more smoothly.
Equipped with a DC brushless inverter motor, quiet and energy saving
Equipped with a new quick release fixture for easy calibration assembly
Equipped with new tungsten steel cutters

Best Key Cutting Machine

The 4way vises can refer any double-sided grooved keys, and can use the key gauge to place shouldered keys on right position of grooved vise.
The special using of vise carriage can be locked into the stationary or into swivel position.

Specifications:
Dimensions: 360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 Cuft

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

Keys Cutting Machine

The 2 way vise can refer your need to hold till 128mm key and any type of double side grooved key.
Both upper and lower section of the vise duplicate 128mm keys and special / unusual keys that extra adapter is needed.

Specifications:
Dimensions: 360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

High Security Key Machine

GL-035 machine can duplicate any kind of keys without limitation in length.
Safety micro switch protection.
Horizontal sliding feeding table (it make cutting more precise)
Plastic safety cover to avoid steel/brass…ETC. (dust from splashing out).
C/W tungsten carbide cutter.
4-ways jaws (it can clamp a large variety of blanks keys including double sided keys).

Specifications:
Dimensions: 265 mm(W)*275mm(D)*335mm(H)
N.W. 16 Kg
G.W. 18 Kg
Meas. 2.48 CUFT

Motor: Single phase, 90W, Rpm3450
110V or 220V, 1.7A

Key Code Cutting Machine

THIS custom-made, versatile code machine cuts keys with different angles of inclination for either right-or Left-turn keys. Suitable for factory production, it duplicates four keys of one code simultaneously.

Specifications:
Dimensions: 56cm(W)*83cm(D)*113cm(H)
N.W. 170 Kg
G.W. 220 Kg
Meas. 19 CFT

Motor: 3Phase, 1 Hp, R.P.M. 1725
380V or 220v, 50 Hz

Automatic Key Machines

Special designed digital controlled key making machine may make semi-circular or square key by changing vise only.
Production upon customer's exclusive requirement of specification.
Automatic code selection by computer & permit user to set up cycle number freely upon their requirement.
Equipped by tungsten cutters.
Easy to operate, save time and efficiency!

Specifications:
Dimensions: 126cm(W)*68cm(D)*117cm(H)
N.W. 300 Kg
G.W. 350 Kg

Motor: 3 Phase, 1 Hp, R.P.M. 1725
380V or 220v, 50 Hz

Tubular Key Cutting Machine

This is the spare parts main for portable tubular key machine that can cut standard size scquence tubular keys by code with no motor.

Specifications:
Dimensions: 110 mm(W)*160mm(D)*70mm(H)
N.W. 0.4 Kg
G.W. 0.7 Kg
Meas. 0.04 CUFT

Key Copying Machine

Multi-functional keys duplicating machine, can be copied all kinds of double-sided grooved keys.

The 4 way vise can refer your need to hold till to 100mm key and any type of double side grooved key.
Both upper and lower section of the vise duplicate 110mm keys and special / unusual keys that no extra adapter is needed. Ex. Semi-circular key, Square key, Round shaft key.

Specifications:
Dimensions: 360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

Copy Key Machine

The specially designed two horizontal motion wheels control the motions of carriages individually, with the golden wheel controls the right carriage and the small white handle controlling the left one.

Specifications:
Dimensions: 360 mm(W)*310mm(D)*240mm(H)
N.W. 20 Kg
G.W. 22 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/5 Hp
110V or 220v, 50 HZ or 60 HZ

Key Cutting Tools

This product is equipped with a steel blade material, and with the baseline. All keys can be cut, including car and motorcycle keys. It's the prompt and efficient tool, and a best tool to unlock it out.

Specifications:
N.W.0.5Kg
G.W.0.55Kg

Keys Maker Machine

Easy Operating, Simple Style manual machine.
4 way jaws which can clamp a large variety of key blank including double sided keys.
Equipped with High Speed Steel single angle cutter.
Fixing knobs with bearing ball can help to hold the key tightly.
High precise, save times & elevate efficiency.

Specifications:
Dimensions: 300 mm(W)*215mm(D)*320mm(H)
N.W. 14 Kg
G.W. 16 Kg
Meas. 2.48 CUFT

Motor: Single Phase, 1/4 Hp, R.P.M. 1720
110V or 220v, 50 HZ or 60 HZ

Key Cutting Equipment

This machine is for carrying out the work, with 12V car charger electricity.
It's having with the rechargeable batteries, solved the uneasy on power issue outsider.
It can copy all the types of keys, including any type of double side grooved key, car keys, motorcycle keys, etc., no extra accessory is required.
The 4-ways vise can refer your need to hold till to 128mm key.
Equipped with V type Tungsten cutter.
Equipped with Nylon Brush.

Specifications:
Dimensions: 210 mm(W)*250mm(D)*160mm(H)
N.W.: 8 Kg G.W.: 9 Kg
Meas. 0.8 Cuft
Motor: 110V or 220v，50 HZ or 60 HZ
12VDC

Duplicate Key Making Machine

New style patented multifunctional key duplicating machine

New style patented base horizontal flip designed, can move forward, backward, left and right.
The cutting key has no bevel; the base is turned over for easy gripping of the key
The newly designed four-sided jaw can be directly and easily rotated to change sides.
Can be directly prepared with remote control car key, long key... etc.
Equipped with LED lamps
Equipped with automatic power-off protection device

Specifications:
Dimensions：380 mm(W)*193mm(D)*220mm(H)
N.W. 9 Kg
G.W. 11 Kg
Meas. 1.42 CUFT
Motor: 100W
110v/220v 50 HZ / 60 HZ

Key Coding Machine

THIS productive key code machine is suitable for key factory production.
The system is fit with Abloy®, Abus®, customer-specialized, four keys per time.
It’s using different tilt angle cutting for either right or left-turned keys by 4 pcs of tungsten cutters.
With an emergency stop switch.
Easy to operate, save time and efficiency!

Specifications:
Dimensions: 56cm(W)*83cm(D)*113cm(H)
N.W. 170 Kg
G.W. 220 Kg
Meas. 19 CFT

Motor: 3Ph

According to customers' demanded to produce this machine whether it is a semi-circular or square keys.

Automatic Key Machine

Special designed digit control key making machine may make semi circular or square key by changing vise only.
This is production upon customer's exclusive requirement of specification.
For automatical code selection by computer & permit user to set up cycle number freely upon their requirement.
Equipped tungsten carbide cutters.

Specifications:
Dimensions: 126cm(W)*68cm(D)*117cm(H)
N.W. 300 Kg
G.W. 350 Kg
Motor: 3 Phase, 1 Hp, R.P.M. 1725
380V or 220v, 50 Hz

Key Cut Machine

GL-320 manual keys duplicator is a lightweight, suitable for carrying out the work, can be equipped with indoor electric power or car charger. It weighs only 7 kg, can copy the types of keys, including any type of double side grooved key, car keys, motorcycle keys, etc., no extra accessory is required.

Optional AC or DC voltage.
The 4-ways vise can refer your need to hold till to 115mm key.
Can copy any type of double side grooved key, car keys, motorcycle keys, etc., no extra accessory is required.
With lightweight easy to use.
Equipped with V type HSS cutter.
Rechargeable Power Battery Optional.

Specifications:
Dimensions: 210 mm(W)*250mm(D)*160mm(H)
N.W.: 7 Kg G.W.: 8 Kg
Meas. 0.8 Cuft
Motor: 110V or 220v, 50 HZ or 60 HZ
12VDC / 110W, R.P.M. 3200

Code Key Cutting Machine

It's OEM, customer-made, versatile code machine cuts keys with different angles of inclination for either right-or left-turn keys.

Specifications:
Dimensions: 285 mm(W)*255mm(D)*240mm(H)
N.W. 16 Kg
G.W. 18 Kg
Meas. 2.48 CFT

Motor: Single Phase, 1/5 Hp, R.P.M. 1675
110V or 220v, 50 Hz or 60 Hz

Tubular Key Machine

This lock pick tool is main for portable easy-carried key machine, it can cut standard size scquence tubular keys by code with tungsten cutters.

Specifications:
Dimensions: 110 mm(W)*160mm(D)*70mm(H)
N.W. 0.4 Kg
G.W. 0.7 Kg
Meas. 0.04 CUFT

Key Clip

With this product, you can clip all kinds of plate keys including car key and motorcycle keys.
This is common used when it needs to clip.
With lightweight easy to use, save times and elevate efficiency.

Specifications:
N.W.0.5Kg
G.W.0.55Kg

Key Milling Machine

Special designed milling machine can make any kind of groove of key upon your requirement by changing suitable cutter. High precise, Save times & elevate efficiency. Equipped with 23 pcs different cutters.

Specifications:
Dimensions: 260 mm(W)*420mm(D)*330mm(H)
N.W. 23 Kg
G.W. 25 Kg
Meas. 3.24CUFT

Motor: Single phase, 1/5 HP
110V or 220V, 50HZ or 60 HZ

Magnifier Tools

This picker that is based on high technical medical instruments is developed to be high efficient pick tools in locksmiths field. It can help locksmiths to deal with the problem of even high-level vehicle like Benz & B.M.W.
Combined with searchlight, high efficient magnifier & super harden picking bar, it can see through various type of wafer cylinders to help you pick cylinder & make a new keys for car or/and motorcycle lock. Easy operation & save your times.

Specifications:
Dimensions: 110 mm(W)*28mm(D)*190mm(H)
N.W.0.2Kg
G.W.0.3Kg

Tubular Lock Pick

The GL-205 is new product of tubular lock Picker. It can be used to pick up 7 pins standard Tubular lock (outside diameter 9.6mm & inner diameter 7.85 mm/7.9mm) easily. You can use our GL-T33P to produce a new key accordingly.

Specifications:
Dimensions: 18 mm(W)*70mm(D)*40mm(H)
N.W. 0.02 Kg
G.W. 0.025 Kg

Pick Set

4 pick blades for Pin and Disc Tumbler Locks
5 pick blades for Dimple key systems
1 extractor blade
1 tension tool

Specifications:
Dimensions: 18 mm(W)*70mm(D)*40mm(H)
N.W. 0.4 Kg
G.W. 0.3 Kg